FOR NEW WOOD
Wood article to be coated must be dry & free of dust & loose particles. Sand surface along the grains with emery paper #180.
|1||Recommended use||Interior wood applications|
|2||Product description||Two component acid cured clear finish|
|3||Mixing ratio|| Base——–90 parts by volume.
Hardner—–10 parts by volume.
Thinner—–20 – 40 parts by volume.
|4||Application Viscosity|| For spraying – —15 – 20 sec by ford cup B4 @30°c.
For brushing – —20 – 25 sec by ford cup B4 @30°c.
|5||Maturation time||30 minutes.|
|6||Pot life of mixture||8 hours.|
|7||Recommended spray ressure||30 – 40 PSI|
|8||Recommended DFT||25 – 30 microns|
|9||Drying characteristics 30 c & Relative humidity below 75%|| Surface dry—–20minutes.
Sanding dry —-3 – 4 hours
Fully Cured—–7 days for solvent &chemical
|10||Recoating time||5 – 6 hours.|
|11||Thinner recommended|| For spraying – # 424
For brushing – # 406
|12||Covering capacity @ 25 micron DFT|| 5 – 6 sq.mtrs/litre/coat by spraying.
8 – 10 sq.mtrs/litre/coat by spraying.
|13||Finish||Smooth, Matt and Glossy.|
|14||Packing||500 ml, 1 ltr, 4 ltrs, 20 ltrs.|
|15||Shelf life|| 3 year in unopened conditions in original
container when store in cool & dry place @ 25 ±5°C.
» SEALER COAT
Apply one or two coat of woodpol natural finish clear sealer and allow it to dry for minimum of 5-6 hours. Sand with emery paper #320 or 400 between application of successive coat.
» FINISH COAT
Select finish available in matt or glossy. Alternatively the two can be mix in desire proportions for semi glossy to satin finish of desire sheen. Apply one or two coats of woodpol natural wood finish clear matt or glossy & allow it to dry for minimum of 5-6 hours. Sand with emery paper #320 & 400 between application of successive coat.
FOR PRE POLISHED WOOD
Sand the surface along the grain with emery paper #100 or #180 followed by #320 or 400 to a uniform smooth surface. If staining is desired, completely remove the old finish by using EASY STRIPP Paint & Varnish Remover. Follow step number (2) & (3) recommended above for new wood.
WOODPOL NATURAL WOOD FINISH CLEAR – MELAMINISED
» Stir the contents well before use since soft sedimentation may occur in matt and sealer finish on storage. Strain through musclin cloth in glass or plastic container. Mixing pot, stirrer & spray gun should be free of moisture since system is sensitive to moisture.
» Mix only required amount of Base & Hardner to be used. Do not transfer unused or Left – over material after used into original container as it cause the whole container to gelled up.
» Since system have limited Pot-life (after mixing Base & Hardner) after which they should not be used.
» Recoating and Hard dry time may be more in case of High humid conditions and/or low ambient temperature.
» Coverage & dry time varies depend on film thickness, quantity of thinner used & nature of wood.
NOTE: Product code 08,09,10 Woodpol Natural Wood Finish Crystal Clear Melaminised (Non yellowing) is color less in appearance & it gets yellow after 2 to 3 years and rest of the procedure and properties are same as regular Melaminised wood finish.
HEALTH AND SAFETY INFORMATION
» Handle products in areas of good ventilation. Avoid inhaling vapours since product contains volatile organic solvents.
» Wear normal protective overalls. Solvent resistant hand gloves, eye goggles are recommended. Avoid skin contact.
» The product is flammable and the container should therefore be kept away from fire & spark or any ignition source.
STORAGE, HANDLING & DISPOSAL
» Store in original container in cool, dry & well ventilated place.
» While Handling, avoid inhalation and skin contact. Force ventilation or fresh air mask should be used in confined spaces.
» Dispose in land filling and not in drain or water ways.
There are no reviews yet.