Woodpol Interior PU (Italian Type) (31A)

288.0017,611.00

WOODPOL Exterior is a new generation Two Pack, air-drying Polyurethane coating which can be applied on all types of wood, wood substrate & metals. This high performance NON – YELLOWING coating offer superior & long lasting protection against UV degradation & hence ideal for Exterior applications.

Clear selection
Compare
SKU: N/A Category:

Description

APPLICATIONS PROCEDURE
Wooden article to be coated must be dry & free of dust & loose particles. Prepare smooth surface by sanding with emery paper #180 followed by #320 or #400. Cracks if any should be filled & levelled.

SEALER COAT
Apply one or two coat of WOODPOL Exterior PU clear sealer, depending upon surface smoothness and allow it to dry for minimum of 12 hours. Sand with emery paper # 320 or # 400 between application of successive coat.

FINISH COAT:
Select Finish coat available in Glossy & Matt. Apply one or two coats of GLOSSPOL SUPREME Interior PU – clear and allow it to dry for minimum of 8 hours. Sand with emery paper #320 or #400 between application of successive coats. For better protection apply an additional coat.

GENERAL INFORMATION:
»  Stirr the contents well before use since soft sedimentation may occur in matt and sealer finish on storage. Strain through musclin cloth in glass or plastic container. Mixing pot, stirrer & spray gun should be free of moisture since system is sensitive to moisture.
»  Mix only required amount of Base & Hardner to be used. Do not transfer unused or Left-over material after used into original container as it cause the whole container to gelled up.
»  Use within one week after opening Base & Hardner container.
»  Since system have limited Pot-life (after mixing Base & Hardner) after which they should not be used.
»  Recoating and Hard dry time may be more in case of high humid conditions and/or low ambient temperature.
»  Coverage & dry time varies depend on film thickness, quantity of thinner used & nature of wood.

APPLICATION GUIDE

1   Mixing ratio   Woodpol Interior PU – Base 80 parts by volume.
Woodpol Interior Interior PU – Hardner 20 parts by volume.
Woodpol Interior Interior PU – Thinner 15 – 30 parts by volume.
2   Spray Viscosity   15 – 20 secs on Ford cup B4@ 30 °C.
3   Maturation time   30 minutes
4   Pot-life of mixture   3 – 4 hours at 30°c.
5   Method of application   Spraying.
  Spray Pressure   30 – 40 psi.
6   Recommended DFT   30 – 35 microns per coat.
7   Drying characteristics @ 30°c & relative humidity below 75%   Touch-dry            30 minutes.
Dust-free             2 hours.
Tack-free             3 hours.
Sanding-dry        12 hours.
Hard-dry              Overnight.
Fully Cured           7 days for solvent &chemical resistance.
  Recoating time   12 hours @ 30°C.
8   Theoritical covering capacity @ 30 micron DFT   8 – 10 m2/litre per coat dependent on method of application.
9   Shelf life   6 months in unopened condition in original container when stored in cool & dry place, @ 25±5°C.
10   Packing   250 ml, 500 ml, 1ltr, 20 ltrs.

HEALTH AND SAFETY INFORMATION
»  Handle products in areas of good ventilation. Avoid inhaling vapours since product contains volatile organic solvents.
»  Wear normal protective overalls. Solvent resistant hand gloves, eye goggles are recommended. Avoid skin contact.
»  The product is flammable and the container should therefore be kept away from fire & spark or any ignition source.

STORAGE, HANDLING & DISPOSAL
»  Store in original container in cool, dry & well ventilated place.
»  While handling, avoid inhalation & skin contact. Force ventilation or fresh air mask should be used in confined spaces..
»  Disposal in land filing & not in drain or water ways.

Additional information

Pack size

, , , ,

Resources

Download file here

Clear Sealer (Italian Type)

Reviews

There are no reviews yet.

Be the first to review “Woodpol Interior PU (Italian Type) (31A)”

Your email address will not be published. Required fields are marked *