Woodpol Exterior Polyurethene Clear Glossy (19A)

PRODUCTS DESCRIPTION

WOODPOL wood finish is a Single Pack, air-drying Polyurethane system for wood & wood substrate. This clear coating system brings out the grain Pattern & surface texture of wood so well to make it look splendidly natural & show out real charm. Not only it preserves & enhance the natural beauty of wood grain, but also protects from heat, water, tea & coffee stains & insect attack.

For more info CLICK HERE

This product is currently out of stock and unavailable.

Compare

Description

APPLICATIONS PROCEDURE
»  Wooden article to be coated must be dry & free of dust and loose particles. Prepare smooth surface by sanding with emery paper #180 followed by #320.
»  Apply good quality of wood filler using a musclin cloth or putty knife. Remove excess filler & allow to dry for 2 – 3 hours. Sand with emery paper #180 followed by #320 between application of successive coat.

APPLICATIONS GUIDE

1 Recommended Uses Interior wood applications
2 Product Description One Pack Polyurethane modified clear finish.
3 Supply Viscosity 60 ± 30 sec. on ford cup B4@30 °C.
4 Thinner Recommended TH – 601 or good quality mineral Terpentine
5 Thinner intake For Brushing – 5 – 10% by volume. For spraying – 20 to 25% by volume.
6 Solid 45 ± 2
7 Specific gravity 0.89 ± 0.02 For spraying – 20 to 25% by volume.
8 Method of applications Brushing/Spraying.
9 Spray Pressure recommended 30 – 40 PSI
10 Recommended DFT 25 – 30 microns
11 Drying time @ 30 ± 2 °C Relative humidity of 60 ± 5% Surface dry – about 1 hour
Hard dray – 24 hours.
12 Recoating time 6 – 8 hours @ 30 ±2 °C& Relative humidity of 65% or below.
13 Theoritical covering 8 -10 m2 / litre/ coat by Brushing.
14 Flash point At or Above 30 °C.
15 Shelf Life 6 months in Unopened conditions in original container when stored in cool & dry place @ 25± 5oc
16 Shades available Oak Yellow, Red Brown, Walnut, Rose wood.
17 Packing 200 ml, 500 ml, 1 ltr, 4 ltrs, 20 ltrs.

»  Select finish available in Clear Matt, Glossy or in transparent shades like Oak Yellow, Rose wood, Walnut & Red Brown. Apply one or two coats of WOODPOL TRANS WOOD PU wood finish and allow to dry for minimum of 6 – 8 hours. Light sand with emery paper #320 between application of successive coats.

INSTRUCTIONS
»  Stir contents well before use since soft sedimentation may occur in matt & sealer finish on storage. Strain through musclin cloth.
»  It is recommended to transfer WOODPOL TRANS WOOD PU finish from half filled container (left over after use) to other smaller container to avoid air-gap in the container if not to be use immediately.
»  Close container tightly after use.
»  Do not mix stains.
»  Recoating & Touch dry time be more in case of high humidity and/Iow room temperature.
»  Coverage & dry time varies & depend on film thickness, quantity of thinner use & nature of wood.
»  The product is flammable and the container should be therefore be kept away from fire & sparks or any ignition source.

HEALTH AND SAFETY INFORMATION :
»  Handle the product in areas of good ventilation. Avoid inhaling vapours since product contains volatile solvents.
»  Wear normal protective overalls, Solvent resistant hand gloves, eye goggles are recommended. Avoid skin contact.

STORAGE, HANDLING & DISPOSAL :
» Store in original container in cool, dry & well ventilated place.
»  While handling, avoid inhalation and skin contact. Force ventilation or fresh air mask should be used in confined areas.
»  Dispose in land filling and not in drain or water ways.

Additional information

Color

Oak Yellow, Red Brown, Rose Wood, Walnut

Pack size

, , , ,

Resources

Download file here

Clear Glossy Exterior

Reviews

There are no reviews yet.

Be the first to review “Woodpol Exterior Polyurethene Clear Glossy (19A)”

Your email address will not be published. Required fields are marked *