CLEAR SEALER (ACRYLIC) – BASE

216.0011,859.00

WOODPOL Interior is a new generation Two Pack, air-drying polyurethane coating which can be applied on all types of wood, wood substrate & metals. This high performance coating offer superior & long lasting protection & maintain new look & original beauty for years.

Clear selection
Compare
SKU: N/A Category:

Description

APPLICATIONS PROCEDURE
Wooden article to be coated must be dry & free of dust & loose particles. Prepare smooth surface by sanding with emery paper # 180 followed by # 320 or # 400. Cracks if any should be filled & levelled.

SEALER COAT
Apply one or two coats of WOODPOL Interior PU clear sealer depending upon surface smoothness and allow it to dry for minimum of 8 hours. Sand with emery paper # 320 or # 400 between application of successive coat.

FINISH COAT
Select Finish coat available in Glossy & Matt. Apply one or two coats of WOODPOL Interior PU – clear and allow it to dry for minimum of 8 hours. Sand with emery paper # 320 or # 400 between application of successive coats. For better protection apply an additional coat.

GENERAL INFORMATION:
»  Stir the contents well before use since soft sedimentation may occur in matt and sealer finish on storage. Strain through musclin cloth in glass or plastic container. Mixing pot, stirrer & spray gun should be free of moisture since system is sensitive to moisture.
»  Mix only required amount of Base & Hardner to be used. Do not transfer unused or Left-over material after used into original container as it cause the whole container to gelled up.
»  Use within one week after opening Base & Hardner container.
»  Since system have limited Pot-life (after mixing Base & Hardner) after which they should not be used.
»  Recoating and Hard dry time may be more in case of high humid conditions and/or low ambient temperature.
»  Coverage & dry time varies depend on film thickness, quantity of thinner used & nature of wood.

APPLICATIONS GUIDE

  Mixing ratio Woodpol Interior PU – Base 80 parts by volume
Woodpol Interior PU – Hardner 20 parts by volume.
Woodpol Interior PU – Thinner 15 – 30 parts by volume.
  Spray Viscosity   15 – 20 secs on Ford cup B4@ 30 °C.
  Maturation time   30 minutes
  Pot-life of mixture   3 – 4 hours at 30°c.
  Method of application   Spraying.
  Spray Pressure   30 – 40 psi.
  Recommended DFT   30 – 35 microns per coat.
  Drying characteristics @ 30°c & relative humidity below 75%   Touch-dry            30 minutes.
Dust-free             2 hours.
Tack-free             3 hours.
Sanding-dry          8hours.
Hard-dry              Overnight.
Fully Cured           7 days for solvent &chemical resistance.
  Recoating time   8 hours @ 30°c.
  Theoritical covering capacity @ 30 micron DFT    8 – 10 m2/litre per coat dependent on method of application. 6 months in unopened condition in original
  Shelf life   container when stored in cool & dry place, @ 25±5°c.
  Packing   250 ml, 500 ml, 1ltr, 20 ltrs.

HEALTH AND SAFETY INFORMATION
»  Handle products in areas of good ventilation. Avoid inhaling vapours since product contains volatile organic solvents.
»  Wear normal protective overalls. Solvent resistant hand gloves, eye goggles are recommended. Avoid skin contact.
»  The product is flammable and the container should therefore be kept away from fire & spark or any ignition source.

STORAGE, HANDLING & DISPOSAL
»  Store in original container in cool, dry & well ventilated place.
»  While handling, avoid inhalation & skin contact. Force ventilation or fresh air mask should be used in confined spaces..
»  Disposal in land filing & not in drain or water ways.

Additional information

Pack size

, , , ,

Resources

 Download file here

CLEAR SEALER (ACRYLIC) – BASE

Reviews

There are no reviews yet.

Be the first to review “CLEAR SEALER (ACRYLIC) – BASE”

Your email address will not be published. Required fields are marked *