Description
APPLICATIONS PROCEDURE
» Wooden article to be coated must be dry & free of dust and loose particles. Prepare smooth surface by sanding with emery paper #180 followed by #320.
» Apply good quality of wood filler using a musclin cloth or putty knife. Remove excess filler & allow to dry for 2 – 3 hours. Sand with emery paper #180 followed by #320 between application of successive coat.
APPLICATIONS GUIDE
| 1 | Recommended Uses | Interior wood applications |
| 2 | Product Description | One Pack Polyurethane modified clear finish. |
| 3 | Supply Viscosity | 60 ± 30 sec. on ford cup B4@30 °C. |
| 4 | Thinner Recommended | TH – 601 or good quality mineral Terpentine |
| 5 | Thinner intake | For Brushing – 5 – 10% by volume. For spraying – 20 to 25% by volume. |
| 6 | Solid | 45 ± 2 |
| 7 | Specific gravity | 0.89 ± 0.02 For spraying – 20 to 25% by volume. |
| 8 | Method of applications | Brushing/Spraying. |
| 9 | Spray Pressure recommended | 30 – 40 PSI |
| 10 | Recommended DFT | 25 – 30 microns |
| 11 | Drying time @ 30 ± 2 °C Relative humidity of 60 ± 5% | Surface dry – about 1 hour Hard dray – 24 hours. |
| 12 | Recoating time | 6 – 8 hours @ 30 ±2 °C& Relative humidity of 65% or below. |
| 13 | Theoritical covering | 8 -10 m2 / litre/ coat by Brushing. |
| 14 | Flash point | At or Above 30 °C. |
| 15 | Shelf Life | 6 months in Unopened conditions in original container when stored in cool & dry place @ 25± 5oc |
| 16 | Shades available | Oak Yellow, Red Brown, Walnut, Rose wood. |
| 17 | Packing | 200 ml, 500 ml, 1 ltr, 4 ltrs, 20 ltrs. |
» Select finish available in Clear Matt, Glossy or in transparent shades like Oak Yellow, Rose wood, Walnut & Red Brown. Apply one or two coats of WOODPOL TRANS WOOD PU wood finish and allow to dry for minimum of 6 – 8 hours. Light sand with emery paper #320 between application of successive coats.
» Light sand with emery paper # 320. Clean the surface free of dust, grease & loose particles & follow step no (2) & (3) also old polish or coating can be removed completely by using WOODPOL Paint & Varnish Remover.
INSTRUCTIONS
» Stir contents well before use since soft sedimentation may occur in matt & sealer finish on storage. Strain through musclin cloth.
» It is recommended to transfer WOODPOL TRANS WOOD PU finish from half filled container (left over after use) to other smaller container to avoid air-gap in the container if not to be use immediately.
» Close container tightly after use.
» Do not mix stains.
» Recoating & Touch dry time be more in case of high humidity and/Iow room temperature.
» Coverage & dry time varies & depend on film thickness, quantity of thinner use & nature of wood.
» The product is flammable and the container should be therefore be kept away from fire & sparks or any ignition source.
HEALTH AND SAFETY INFORMATION :
» Handle the product in areas of good ventilation. Avoid inhaling vapours since product contains volatile solvents.
» Wear normal protective overalls, Solvent resistant hand gloves, eye goggles are recommended. Avoid skin contact.
STORAGE, HANDLING & DISPOSAL :
» Store in original container in cool, dry & well ventilated place.
» While handling, avoid inhalation and skin contact. Force ventilation or fresh air mask should be used in confined areas.
» Dispose in land filling and not in drain or water ways.
Reviews
There are no reviews yet.