Description
APPLICATIONS PROCEDURE
Wooden article to be coated must be dry & free of dust & loose particles. Prepare smooth surface by sanding with emery paper # 180 followed by # 320 or # 400. Cracks if any should be filled & levelled.
SEALER COAT
Apply one or two coats of WOODPOL Interior PU clear sealer depending upon surface smoothness and allow it to dry for minimum of 8 hours. Sand with emery paper # 320 or # 400 between application of successive coat.
FINISH COAT
Select Finish coat available in Glossy & Matt. Apply one or two coats of WOODPOL Interior PU – clear and allow it to dry for minimum of 8 hours. Sand with emery paper # 320 or # 400 between application of successive coats. For better protection apply an additional coat.
GENERAL INFORMATION:
»  Stir the contents well before use since soft sedimentation may occur in matt and sealer finish on storage. Strain through musclin cloth in glass or plastic container. Mixing pot, stirrer & spray gun should be free of moisture since system is sensitive to moisture.
»  Mix only required amount of Base & Hardner to be used. Do not transfer unused or Left-over material after used into original container as it cause the whole container to gelled up.
»  Use within one week after opening Base & Hardner container.
»  Since system have limited Pot-life (after mixing Base & Hardner) after which they should not be used.
»  Recoating and Hard dry time may be more in case of high humid conditions and/or low ambient temperature.
»  Coverage & dry time varies depend on film thickness, quantity of thinner used & nature of wood.
APPLICATIONS GUIDE
| Â Â Mixing ratio | Woodpol Interior PU – Base 80 parts by volume Woodpol Interior PU – Hardner 20 parts by volume. Woodpol Interior PU – Thinner 15 – 30 parts by volume. |
|   Spray Viscosity |   15 – 20 secs on Ford cup B4@ 30 °C. |
| Â Â Maturation time | Â Â 30 minutes |
|   Pot-life of mixture |   3 – 4 hours at 30°c. |
| Â Â Method of application | Â Â Spraying. |
| Â Â Spray Pressure | Â Â 30 – 40 psi. |
| Â Â Recommended DFT | Â Â 30 – 35 microns per coat. |
|   Drying characteristics @ 30°c & relative humidity below 75% |   Touch-dry            30 minutes. Dust-free             2 hours. Tack-free             3 hours. Sanding-dry          8hours. Hard-dry             Overnight. Fully Cured           7 days for solvent &chemical resistance. |
|   Recoating time |   8 hours @ 30°c. |
| Â Â Theoritical covering capacity @ 30 micron DFT | Â Â 8 – 10 m2/litre per coat dependent on method of application. 6 months in unopened condition in original |
|   Shelf life |   container when stored in cool & dry place, @ 25±5°c. |
| Â Â Packing | Â Â 250 ml, 500 ml, 1ltr, 20 ltrs. |
HEALTH AND SAFETY INFORMATION
»  Handle products in areas of good ventilation. Avoid inhaling vapours since product contains volatile organic solvents.
»  Wear normal protective overalls. Solvent resistant hand gloves, eye goggles are recommended. Avoid skin contact.
»  The product is flammable and the container should therefore be kept away from fire & spark or any ignition source.
STORAGE, HANDLING & DISPOSAL
»  Store in original container in cool, dry & well ventilated place.
»  While handling, avoid inhalation & skin contact. Force ventilation or fresh air mask should be used in confined spaces..
»  Disposal in land filing & not in drain or water ways.
Reviews
There are no reviews yet.